常州亿创钣金加工厂专业从事精密钣金加工、激光切割加工为主的钣金加工型厂家

幸运飞艇计划

幸运飞艇计划
网站首页 > 注册 > 时事新闻

幸运飞艇计划官网

2018-12-28 08:49:43 常州亿创钣金加工厂 阅读

保养好单层玻璃冷凝器,让其在使用中少出现故障,同是让您也省去了不少烦恼。在日常的操作使用中,如何更好的应用单层玻璃冷凝器,使其发挥它的最大价值。这时候您就不得不了解单层玻璃冷凝器幸运飞艇计划是如何保养的? 1、用前仔细检查仪器,玻璃瓶是否有破损,各接口是否吻合,注意轻拿轻放。

Maintenance of single-layer glass condenser, so that it rarely fails in use, the same allows you to save a lot of trouble. In daily operation and use, how to better apply single-layer glass condenser to make it play its maximum value. At this point, you have to understand how the single-layer glass condenser is maintained? 1. Check the instrument carefully before use. Whether the glass bottle is damaged or not, and whether the interfaces are identical. Take care to handle it lightly. 2、用软布(可用餐巾纸替代)擦拭各接口,然后涂抹少许真空脂。(真空脂用后一定要盖好,防止灰砂进入。)

2. Wipe the interfaces with soft cloth (napkins can be used instead) and then apply a little vacuum grease. (Vacuum grease must be well covered to prevent sand from entering.)

3、单层玻璃冷凝器各接口不可拧得太紧,要定期松动活络,避免长期紧锁导致连接器咬死。

3. The interface of single-layer glass condenser should not be tightened too tightly, so loosen the loosening collar regularly to avoid the long-term locking leading to the connector biting.

4、先开电源开关,然后让机器由慢到快运转,停机时要使机器处于停止状态,再关开关。

4. Turn on the power switch first, and then let the machine run from slow to fast. When the machine stops, turn off the switch.

5、各处的聚四氟开关不能过力拧紧,容易损坏玻璃。

5. Polytetrafluoro switches everywhere should not be tightened too tightly, which is easy to damage the glass.

6、每次使用完毕必须用软布擦净留在机器表面的各种油迹,污渍,溶剂剩留,保持清洁。

6. After each use, all kinds of oil marks, stains and solvents left on the surface of the machine must be wiped off with a soft cloth to keep it clean.

7、停机后拧松各聚四氟开关,长期静止在工作状态会使聚四氟活塞变形。

7. The PTFE piston will be deformed if the PTFE switches are unscrewed after shutdown, and the PTFE piston will be stationary for a long time.

8、定期对密封圈进行清洁,方法是:取下密封圈,检查轴上是否积有污垢,用软布擦干净,然后涂少许真空脂,重新装上即可,保持轴与密封圈滑润。

8. Clean the sealing ring regularly by removing the sealing ring, checking whether there is dirt on the shaft, wiping it with a soft cloth, then applying a little vacuum grease and reloading it to keep the shaft and sealing ring smooth.

9、电气部分切不可进水,严禁受潮。

9. Electrical parts must not be flooded and damp is strictly prohibited.

10、必须采购原厂正宗配件,随意使用其他配件对机器会造成致命的损害。

10. Authentic parts must be purchased from the original factory. The use of other parts at will will will cause fatal damage to the machine.

11、对单层玻璃冷凝器做任何修理或检查时,一定要先切断电源,水源。

11. When repairing or inspecting a single-layer glass condenser, the power supply and water source must be cut off first.

辛苦整理!转载请注明来自 http://www.zqshzb.com/n1b/3025.html



标签:   钣金加工 冷凝器 钣金 加工